Powered Turntable Truck with Steel Sides

Powered Turntable Truck with Steel Sides part of the UK’s Favourite HI-POW Powered Trolleys Range, made here in the Southwest with 20 years of experience manufacturing powered trolleys. Handle-iT is head and shoulders above the competition with both knowledge of the products and the components within the product. The Handle iT industry standard powered pallet truck configuration provides immediate familiarity with the controls. The Handle has an automatic return to the upright position, where the electromagnetic brake engages to stop accidental movement of the trolley without the operator making the positive decision to lower the handle and engage the throttle. This handle works the same way in the down position, so in the unfortunate event that the operator were to trip or slip, the handle in the down position would also stop the motor dead, to ensure that the operator was not run over after their fall. Whilst the emergency stop button strategically placed ensures that if the operator backed into a wall, the emergency stop button would hit the operator and the trolley will stop dead, ensuring that the operator is not trapped. Moreover, the trolley key would then need to be reset to ensure the deliberate movement of the trolley, rather than accidental.  With simple slide in slide out turned steel side panels to help retain the load. Both Side panel kit and the corner posts are all removable so if the load is bigger than the trolley … no problem, they can be removed in seconds, turning the Powered Turntable Truck with Steel Sides into a standard Powered Turntable Truck, making this a super flexible truck to assist with all product movement over any ground. The chassis is constructed using 50mm x 25mm box section, which is crafted via laser cutting technology to ensure additional strength due to the single piece construction, meaning no mitred cuts. This also ensures there are no sharp edges to hit pedestrians or your facility.

User Interface With and ergonomically positioned handle, and robust user interface, the butterfly throttle is perfectly positioned to provide 400w of high torque power directly through the transaxle. Intelligent Battery indicators give clear LED light instruction to tell you the exact state of your battery charge, with a 20km range between charges this lets you know exactly when you need to return to base for a charge and battery swap. The variable speed adjustment, allows you to set the trolley speed directly on the operator controls, allowing the operator to restrict the speed in certain areas, for instance where there is a high volume of pedestrians to increase safety. For further control, this parameter can be controlled and set at factory so the speed can be set anywhere between 1 min -6 max kmph. The heavy-duty industrial steel casing for the user interface, is IP54 Rated and then covered with a further moulded Perspex cover. Finally, the anti-trap button, perfectly positions so that if it were to hit the operator, the trolley would automatically brake and go into safety mode so that it couldn’t be moved without reset, stopping any operator getting trapped.

The Intelligent Industrial Chassis with the top shelf positioned at the optimum waist height to make the placing of even heavy loads as safe as possible. It has 18mm WBP plywood surface, mounted in a picture frame constructed from 25mm x 5mm angle iron, giving a flush surface. The base unit is laser cut from a single piece of box section for additional strength and a curvaceous corner that is kinder to any ankles or walls that they may encounter compared to a mitred frame, and considerably stronger than a pressed sheet steel base. Under side, the battery is fully encased in a 2mm thick steel box, eliminating the risk of damage to any lead acid battery or even worse, risking thermal runaway from a pierced lithium battery. The whole unit is controlled by our Curtis Microprocessors which is where the clever bit happens. Control all the parameters within the trolley, acceleration, max speed, regenerative braking characteristics, amber warning beacons, even the audible warnings. Thyristor speed control system makes sure the user is in total control. The more pressure you apply the faster the trolley will move, reduce the pressure and the speed will reduce accordingly, there is no steeping through power steeps that you would get through a transistor control, smooth all the way.

As the HI-POW range is designed and manufactured here in the UK, if you want something a little different, just call the team and we can get the design together for you.

For more information, take the link to our Powered Trolleys info page, or contact the team on 01803 875 222 or at sales@handle-it.com

Powered Trolley Training We are now offering on-site powered trolley operation training for anywhere in the UK. Training for groups of up to 6 people starts at £360 per day, plus travel/accommodation expenses. To arrange training, please contact sales@handle-it.com, or call +44 (0)1803 875 222.